For those that are unfamiliar with RAID, RAID stands for redundant array of inexpensive disks. The idea is that one may provide enhanced reliability or performance by using an array of relatively inexpensive disk drives combined with a special hardware or software controller. The three most common RAID configurations are called RAID 0, RAID 1, and RAID 5. RAID 0, also known as striping, is the division of data between drives such that a single read or write operation may combine data from two or more hard drives, thus increasing the aggregate transfer rate. RAID 1, also known as mirroring, does the opposite of RAID 0: instead of focusing on performance, RAID 1 focuses on increasing reliability by storing multiple copies of your data on different drives, thus reducing the chance of a drive failure destroying your data. I opted to have the workstation preconfigured with RAID 0 for the enhanced performance.

Setting up the Velocity was a breeze: five minutes to get it out of the box and onto my desk and another ten to boot it up and configure it to talk to the network. Those of you who will want to add custom hardware such as a preferred graphics board, gigabit Ethernet or a DVD drive will appreciate the Velocity's maintenance-friendly case with just two thumbscrews between you and the motherboard. Red Hat 7 will recognize most third-party hardware without problems.

There are two big issues to be aware of before you set up the system. One is that the default Red Hat 7 has a long list of known problems, and because of this you may have trouble getting some applications to run properly. The other major issue that I ran into is that the kernel needs special parameters to boot properly from the Promise RAID hardware. This only becomes an issue if you want to replace the kernel or install an alternative Linux distribution; Pogo's default configuration works fine. The usual symptom is a kernel panic when the kernel attempts to mount partitions, but the fix is simply to provide the kernel with the correct I/O addresses. For a detailed explanation of how to do this see Aaron Cline's “Unofficial Asus A7V and Linux ATA100 Quasi-Mini-Howto” at http://www.geocities.com/ender7007/. Once the machine recognizes the card no further configuration is necessary to take advantage of the RAID controller, and other than the issues just mentioned, I had no problems with setup.

My overall first impression is that the Velocity is a very speedy machine—as one would expect from any 1GHz Athlon box—and fairly well put together. As someone who frequently swaps hardware out of my machines I also appreciate the ease of opening the case via the thumbscrew-attached side panels. Having set up the machine and played with it for a little bit, it is time to measure how fast the Velocity really is.

For these benchmarks, the PogoLinux RAID box in RAID 0 mode will be compared to a similarly configured non-RAID system, same motherboard and processor (well, A7Pro vs. A7V), same RAM and a similar ATA 100 drive (but just one for the non-RAID system).

Listing 1. PogoLinux Velocity (RAID 0)

Listing 2. Single Disk System

Using the Bonnie benchmark suite, the PogoLinux box produced some interesting results. Tests that performed large numbers of very small disk transactions did very poorly on the PogoLinux RAID box—about half as fast as the comparison system—while tests that rely on fewer transactions involving larger amounts of data did much better, right in the middle of the 40-50MB/s transfer rate quoted by PogoLinux. This information is very important when one is considering the purchase of approximately $1,578 worth of hardware. So, on to a real-world test.

To compile Mozilla, use the time command for measurement, as shown in Table 1.

Table 1. Times (mm:ss.s) and Improvement (%)

In most applications, the RAID system didn't perform noticeably differently from the single drive system. Some tasks, such as untarring Mozilla, actually came out slower on the RAID system. Compiling Mozilla was only faster by about ten seconds out of 50 minutes. This is indicative of a near-universal truth in computing: aggregation can buy you increased bandwidth, but it can't buy decreased latency. The likely explanation for why the RAID 0 system has relatively poor performance when performing many small accesses is rather lengthy, but suffice it to say that it is related to the fact that having to wait for two read/write heads instead of one increases the array's average seek time.

What this means in the real world is that having a RAID 0 disk system will only accelerate tasks where large amounts of contiguous data is transferred (where increased transfer rates help) and not tasks that require many small disk accesses (where disk latency is more important than transfer rate). One good example of this is working with applications that use large data files, such as editing high-resolution photos in the GIMP, where I did indeed notice significant improvement in loading and saving large files.

Other tasks that benefit from increased disk transfer rates include database searches, video editing or any type of high-bandwidth data capture (i.e., direct-to-disk audio and video). Tasks that won't benefit from RAID 0 (especially as opposed to having two drives operating independently) include file servers serving many concurrent users making small requests, database servers supporting similar workloads, most general-purpose applications and development software, etc.

For many users' purposes, a RAID 0 system will provide less performance benefit than spending the equivalent money on getting a single fast hard drive, faster processor, more RAM or a faster motherboard. The price difference between PogoLinux's Velocity workstation and a similarly configured workstation without RAID, such as PogoLinux's Altura workstation, is about $300 if you still buy another 45GB IBM hard drive. For $300 you can buy a 1.2GHz Athlon (instead of 1.0), an extra 256MB of RAM (or an extra 512MB if you stretch it to $370) or a 64MB GeForce2 GTS (instead of the included 32MB MX). On the other hand, if you really need the maximum throughput for working with large files or the reliability of a RAID 1 configuration, the RAID system is definitely the way to go.

The Good/The Bad